Cricut Metal Engraving: Make Bracelets with Your Cricut Maker

Design

Products You May Like

This post and photos may contain Amazon or other affiliate links. If you purchase something through any link, I may receive a small commission at no extra charge to you. Any supplies used may be given to me free of charge, however, all projects and opinions are my own.

metal engraving with cricut maker

I get all sorts of questions about Cricut metal engraving. So I thought we would make some bracelets today with the Cricut Maker. This project is actually really easy and it is a great way to make personalized gifts for everyone on your list. Make your own metal cuff bracelets with any phrase or font that you would like. I am even offering up tips and tricks for locating your etching on the Cricut Maker mat so you don’t waste as many blanks.

cricut metal engraving

Cricut Metal Engraving

Engraving metal with your Cricut is actually fairly easy. Just grab your Cricut Maker and your engraving tip then click play on the video below!

If you can’t watch the video, read below for my full tutorial!

Supplies needed

supplies for engraving with your cricut maker

Contents of Impress Art Essential Bracelet Kit

The bracelet kit is a great investment as you get everything you need to start making bracelets right away. The kit includes:

  • Bracelet blanks in 2 sizes (4 each)
  • Location guides
  • Stamp enamel
  • Bending bar
  • Bending pliers
impress art bracelet kit

Design Your Bracelet

Let’s take a look in Cricut Design Space and go over how you’re going to design your bracelet. The three bracelet sizes that Impress Art makes are 1/4 inch, 3/8 inch, and 1/2 inch. I’m going to make a 3/8 inch bracelet. First, I made a rectangular box measuring 3/8 by 6 inches.

making bracelet blank in design space

Then, I’m going to type some text. The font I’m using is DTC Porch Chair, and I like it because it’s a little quirky and it’s all capitalized. I prefer the fonts that are capitalized over the fonts that are not capitalized because they tend to fit better on bracelets. I also like to search Cricut fonts and filter them for writing. 

finding writing fonts

Size your text to where it fits on the bracelet by using the rectangle you made as a guide. You can choose both the box and the text and click align then center to center it up. This should help you visualize the bracelet and how it will look once you make it.

sizing text for metal engraving

I am making one version of the bracelet that is drawn with a pen and one that is engraved. I will use the pen version to test my location below. For the engraving option, pull down “operation” and pick “engrave” for the text. NOTE: You will want to make sure that either Maker or Maker 3 is chosen as the machine. Those are the only two machines that can engrave.

choosing engrave lines for cricut maker

Now, we have our boxes with words, click “make it”. Please note that you do not want to attach the boxes to the text. The box will be used for visualizing your bracelet on the mat only. Move the boxes to the same mat as your text and you can use the box for alignment. Pick an area of the mat for your design and line everything up. Once you have everything pretty much centered, then you can pick the blank, and hide it, and we can repeat for as many bracelets as you would like.

locating designs in cricut design space

NOTE: You can do this same procedure for engraving or for testing your location as shown below.

Testing Your Location

I hear from a ton of people that have a hard time locating their Cricut metal engraving. This process helps to test the location so you don’t waste as many blanks. Once you have your design, send the pen version to your Cricut machine in the location that you think you want it in.

Next, let’s put the paper on our mat. I’ve taken the light grip mat, some really thin tissue paper, and my blank. Add the tissue paper to the mat and you can see the gridlines through the paper. Locate your bracelet blank in the same area as you did on the screen in Design Space then trace around it with the Cricut pen.

how to locate engraving on a cricut

Add the pen to my Cricut Maker and you are ready to draw the words onto my tissue paper. Just load your mat and press the go button and let the Cricut draw.

using tissue paper to locate engraving

Once your machine has drawn the words, you can check the location. For instance, the “Choose Joy” is a little low, so I’ll either move the blank down a little bit or the words up a little bit in Design Space to accommodate for this. 

writing on tissue paper with a cricut maker

Let’s take a look in Cricut Design Space at how that will work. We’ll click “make it” with the engraved version of the words. Then repeat the same procedure for locating but this time I’ll take my “Choose Joy” and move it up to the top of the blank. Now it is just a little bit higher than it was before which should put it in the right location.

locating engraving words in cricut design space

Engraving Metal with the Cricut Maker

Next, let’s put our bracelets onto the strong grip mat to do some Cricut metal engraving. The bracelets come with a blue protective film on the front and the back. Just peel that off of both sides and discard it. Next up are some bracelet guides. Normally these are used for hand stamping your bracelets, but I find them super convenient to locate the center for engraving. It has markings to locate the center up and down, and then there’s a marking in the center of the bracelet itself. I like to just make sure I get the locator in the center of the bracelet. 

how to put metal on a cricut mat

Now I have two bracelet blanks with the bracelet guides on them and we’ll just put those on our mat. The first should be at 3 inches down. The left end should be at the 1-inch mark then we want that center mark to be at the 4. The other end should end up at the 7 inch mark. We’ll repeat that for the second blank 5 inches down. Once everything looks centered, we’ll want to tape these into place to make sure that they do not move. I’m just going to tape across both ends and it’s ready for the Cricut Maker. 

adding bracelet blanks to a strong grip cricut mat

Remove any blade that you have in your Maker and put the engraving tip into the machine. I picked stainless steel for my material and moved the white star wheels are all the way to the right.

putting the engraving tip into the cricut maker

Then load your mat once prompted. Once your mat is loaded, all that’s left to do is to hit the “go” button and watch the magic happen.

cricut maker engraving metal

Once your bracelets are done engraving, just eject your mat and take a closer look at your engraving.

engraving bracelet with a cricut maker

You might find some debris, and you can just brush that off. Then, you can just peel back the tape, and remove the blanks from the mat. 

engraving metal on a cricut

Adding Enamel

The next thing to finish off these bracelets is to add enamel! You could use either what comes in the pack or buy a marker separately.

adding stamp enamel to a bracelet blank

It is water-based, so it’s not going to hurt anything. Just add it over the top by either brushing it on or just wiping it with your finger.

stamp enamel on bracelet blanks

It dries in about one to three minutes. Wipe away all that excess with a rag and you’ll be left with the enamel in your engraving. It makes it stand out quite a bit more than when it comes off of the machine.

wiping off stamp enamel from bracelet blanks

Forming Your Bracelet

Finally, we will bend these blanks into actual bracelets. First, we’ll take a bending bar, which has a little lip that holds your bracelet. Put the bracelet in face-up. NOTE: If you have any bracelets you messed up engraving, it is great to start by bending those to get the hang of it.

bending bar for a cuff bracelet

Then, you just push the bracelet down to get the first half of your cuff shape.

bracelet bending bar

Repeat that on the opposite side.

how to bend a cuff bracelet

Use a pair of pliers to get that perfect shape. If you’re finding a place that’s not exactly round, you just squeeze it with those pliers to get that perfect, round bracelet shape. You can also pull the bracelet out to make it larger to fit any wrist. And there you have a cuff bracelet! 

pliers to bend bracelets

Which Cricut machines can engrave metal?

Now I have some really amazing bracelets all made using Cricut metal engraving. I did want to note, this can be used on the Cricut Maker or the Cricut Maker 3. Both will accept the engraving tip and the quick swap housing. Other Cricut machines cannot do metal engraving.

making a metal bracelet on a cricut machine

I hope you enjoyed the hack for making sure that you get your project located correctly too! Use that tissue paper hack. You should get a perfect bracelet every single time. I know I hear from a ton of people that cannot get the location right and this is one way to test before you actually engrave your project.

I would definitely start with the kit from Impress Art as it has everything you need to get started. You can add more blanks or stamp enamel later if you need it.

metal engraving on a cricut maker

Cricut metal engraving is definitely a fun project with amazing results. Imagine a custom bracelet with whatever you want on the front in whatever font you love. This is one of those crafts that you can make over and over again for everyone on your list.

cricut maker engraving tool on metal

So, pick up a kit and try this one for yourself. I think you will really love the results!

metal engraving with cricut maker

Products You May Like

Leave a Reply

Your email address will not be published. Required fields are marked *